CH PRECISION M1 2-CHANNEL REFERENCE POWER AMPLIFIER

49,400 

Đây là ampli đầu bảng của CH Precision, có khả năng khắc chế những cặp loa hi-end hàng đầu. M1 mang trên mình toàn bộ những tinh hoa chế tác của CH, đặc biệt là mạch ExactBias mà một phần mềm nhận biết để phối ghép tối ưu với các dòng loa khác nhau. Ở chế độ stereo, M1 cho công suất tối đa 200 watt/kênh ở trở kháng 8 Ohm. Khi chuyển sang chế độ đấu cầu và hoạt động như một khối mono-block, mỗi khối M1 cho công suất tối đa 700 watt/kênh 8 Ohm. Với biến áp nguồn công suất lên tới 2200 VA, M1 có dòng đủ lớn để ung dung kéo hầu hết mọi đôi loa trên thị trường.

  • Mô tả
  • Đánh giá (0)

Mô tả

Đây là ampli đầu bảng của CH Precision, có khả năng khắc chế những cặp loa hi-end hàng đầu. M1 mang trên mình toàn bộ những tinh hoa chế tác của CH, đặc biệt là mạch ExactBias mà một phần mềm nhận biết để phối ghép tối ưu với các dòng loa khác nhau. Ở chế độ stereo, M1 cho công suất tối đa 200 watt/kênh ở trở kháng 8 Ohm. Khi chuyển sang chế độ đấu cầu và hoạt động như một khối mono-block, mỗi khối M1 cho công suất tối đa 700 watt/kênh 8 Ohm. Với biến áp nguồn công suất lên tới 2200 VA, M1 có dòng đủ lớn để ung dung kéo hầu hết mọi đôi loa trên thị trường.

THÔNG SỐ

Analog inputs
Inputs type Balanced (XLR), one connector per board
Single-Ended (RCA & BNC), one connector per board
Input impedance Balanced: 94kΩ
Single-Ended: 47kΩ or 300Ω
Input stage JFET input stage
Ultra-low noise, discrete fully differential stage
24dB range adjustable gain in 0.5dB steps
Amplification
Amplification stage Ultra-low noise full discrete class AB design
6 pairs of complementary output transistors
Ouptut power 2x 200W / 8Ω, 2x 350W / 4Ω, 2x 600W / 2Ω in stereo and bi-amp modes
1x 350W / 4Ω, 1x 600W / 2Ω, 1x 1100W / 1Ω in monaural mode
1x 700W / 8Ω, 1x 1200W / 4Ω, 1x 1600W / 2Ω in bridge mode
Bias Patent-pending bias circuitry for constant bias operation
Feedback User-adjustable local vs. global feedback ratio, from 0% to 100% in 10% steps
Bandwidth DC to 450kHz (-3dB) at 1W into an 8Ω resistive load
Signal to Noise Ratio Better than 115dB in stereo and bi-amp modes
Better than 118dB in bridge mode
Total Harmonic Distortion + Noise Less than 0.1% with 0% global feedback
Less than 0.01% with 100% global feedback
Analog outputs
Binding posts Two pairs of Argento binding posts for loudspeakers connection
Monitoring Non-intrusive DSP-based protection of the amplifier and connected loudspeakers
Instantaneous voltage & current values are permanently monitored on each channel
Protections Short-circuit protected
Disconnected loudspeaker detected
Over-temperature of the heatsink
Over-temperature of the output transistors
Power supply
Transformer 2’200VA toroidal transformer for output stages, oversized for low-noise operation
100VA separate toroidal transformer for input stages
Power capacitors 2x 100’000uF/100V 4-poles capacitors
Regulators Non-regulated symetrical power supply for the power stages
Eight local regulation stages for input/driver stages
Seven local regulation stages for the logic/display
General
Display 480×272 pixels, 24bits color, AMOLED
Mains operation Selectable 100V, 115, 230V AC, 47-63Hz
Fuses value and location Standby fuse (white holder): 250mA T (230V AC), 500mA T (100V AC, 115V AC)
Audio (mid power) fuse (black holder): 1.6A T (230V AC), 3.15A T (100V AC, 115V AC)
Power fuse (IEC20 holder): 16A T (230V AC), 32A T (100V AC, 115V AC)
Power supply consumption <1W (standby), 2200W max in operation
Dimensions/Weight 440 x 440 x 266mm (W x D x H), 75kg
Remote control Ethernet based system control via the Android CH Control App

 

Đánh giá

Chưa có đánh giá nào. Thêm đánh giá